We use cookies to provide you the best experience on our websitet. More info: Data Protection Statement.
Products Menu
Hungarian hu
English en
Romanian ro


LDG AT-200PROII Click to enlarge
263.70 EUR (219.75 EUR + VAT)
Model: AT-200PROII
Availability: On stock
Average Rating: 5 out of 5 Stars!
Manufacturer: LDG Electronics

Time was, 100 watts was a lot of power. Today, more and more transceivers feature 200 watts output. Even though many of these modern radios feature a built-in tuner, it’s range and features are usually quite limited; if you need a tuner, you probably need a better one than they built into the radio. The LDG AT-200ProII is designed for this new generation of rig. It's specifically recommended for Ten-Tec and tube radios.

Many QRP operators have a small 100-150 watt amplifier for times when you need a few more S-units. The AT-200II is ideal for this kind of operation; it’s minimum required power is only 5 watts, but it will handle the higher power as well. 

The AT-200II will handle up to 250 watts SSB or CW on 1.8 – 30 MHz, and 100 watts on 54 MHz. It features LDG’s state-of-the-art, processor-controlled Switched-L tuner. It will match virtually any kind of coax-fed antenna, including Yagis, dipoles, inverted Vs, slopers, loops, just about anything. It will typically match a 10:1 SWR down to 1.5:1 in just a few seconds. You can also use the AT-200ProII with longwires, random wires and antennas fed with ladder line with the optional LDG balun. 

Operation couldn’t be simpler: while transmitting a carrier, just press the Tune button. An automatic tuning cycle will begin, then end a few seconds later with the tuner set at the lowest SWR (almost instant for frequencies stored in memory). 

The AT-200ProII is the latest in a long line of innovative LDG tuners. Get the most out of your Kenwood, Yaesu, Ten-Tec or Icom radios that operate at higher power.

  • 5 to 250 watts SSB and CW. 100 watts on 6M. 75 watts with PSK or digital modes.

  • Easy to read LED bargraph display for RF power, SWR and status.

  • LEDs for Antenna Position and Bypass.

  • 4,000 memories (2000 for each antenna) for instantaneous band changing.

  • Two position antenna switch with memories for four antennas on each position.

  • Tuning time: 0.5 to 6 seconds full tune, < 0.1 second memory tune.

  • Built in frequency counter for memory operation.

  • Frequency coverage: 1.8 to 54.0 MHz.

  • Tunes 6 to 800 ohm loads (16 to 150 ohms on 6M), 6 to 3600 ohms with optional 4:1 Balun (LDG RBA 4-1).

  • For Dipoles, Verticals, Vees, Beams or and Coax Fed Antenna.

  • Optional external Balun allows tuning of random length, long wire or ladder line fed antennas.

  • Includes 6' DC power cable.

  • Power requirements: 11 to 16 volts DC at 750 mA max during tuning.

  • www.Jameco.com WM1012-760 and 1953663 are compatible power supplies.

  • Enclosure: 9.5D x 7.1W x 2.0H inches.

  • Weight: 2 pounds.
| 5 out of 5 Stars!

Udvarias korrekt kiszolgálás.
Valamennyi antennát gyorsan leillesztette, megéri az árárt.
| 5 out of 5 Stars!

Több hónapos használat utáni tapasztalatok. Valamennyi házi gyártású antennámat sikeresen leillesztette (vertikál, huzalantennák),
a G5RV-vel is simán megbirkózott. Csak Ajánlani tudom. Mint mindig, gyors és pontos kiszolgálás
Write Review

Note: HTML is not translated!
Rating: Bad Good